Search:

Type: Posts; User: Pilot; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    4
    Views
    106

    Re: short shots on a new tool

    hi,
    Ii is not so much informations… Which hot runner nozzle tip do you have? Do They have torpedo, or needle or nothing inside? how big the parts are.... OK. By my opinion you have nozzle with...
  2. Replies
    5
    Views
    206

    Re: krauss maffei ipc sr alarm

    it can be a issue between BR and SR card. Please try to contact KM service for help.
  3. Replies
    5
    Views
    206

    Re: krauss maffei ipc sr alarm

    Is the alarm pop up only when you are purging?
    during injection is it ok?
    Carriage is in back or in forward. (please check carriage position on screen)

    Please do the zero point for injection...
  4. Replies
    3
    Views
    1,990

    Re: WANTED - service contact for Nissei in EUROPE

    name of the Samuray is "Steve" Kato :-)
  5. Replies
    9
    Views
    390

    Re: Blush or Graying at molded part edges

    :-) yes, someone...
  6. Replies
    9
    Views
    390

    Re: Blush or Graying at molded part edges

    By my opinion it is a pressure issue. Wall thickness and cooling of the melt in the tool. Please try to check, if it appears also on the part without holding pressure. than you will see, from which...
  7. Replies
    1
    Views
    105

    Re: Husky Valve location and description

    Which machine do you have?
  8. Replies
    9
    Views
    599

    Re: Delta E Color Tolerance

    Hi,
    I can confirm, that delta E +/- 1,5 is a standard request from various automotive customers.
    what MUST be specified also is a measuring device (Minolta, x-rite usualy) Both sides have to have...
  9. Replies
    2
    Views
    315

    Re: milacron maxima 580wp issue

    please check calibration pages. It looks as lost values for transducer.
  10. Replies
    7
    Views
    585

    Re: Van Dorn 300HT excessive noise

    please check also the oil in oil tank. If is possible také a sample to see potential air inside (oil level mark is not good enough). I vote for air suction.
  11. Replies
    7
    Views
    625

    Re: Injection Graphic

    the velocity depends on machine producer interpretation. some machines have only "absolute" velocity - not depending on direction. Some machines has a velocity counted from linear directly and in...
  12. Replies
    8
    Views
    840

    Re: Gas bubbe on worm thread surface

    please check the sprue and nozzle conditions. wearing, sharp edges.. etc. Do you have hot tips?
  13. Replies
    4
    Views
    518

    Re: Support for Moving side of Mold

    ok, what is "larger tool"? 100kg, 1t, 10t, 40t ????
  14. Replies
    6
    Views
    658

    Re: Line mark on the surface of product

    Thanks for pict. It is not very clear from images, what is going on. It can be also wall thickness issue or pressure marks. Do you have it also on short shots?
  15. Replies
    9
    Views
    913

    Re: Cavities blockage

    how big are the caps? the 12 sec inj. time for HDPE is a loooong time….
  16. Replies
    6
    Views
    658

    Re: Line mark on the surface of product

    could you please insert a picture of whole part and mark a injection gates location?
  17. Thread: Defects

    by Pilot
    Replies
    6
    Views
    1,157

    Re: Defects

    It looks, that the part is overpacked too much...… but this will not solve the sprue issue :-)
  18. Replies
    5
    Views
    636

    Re: Thermolator question

    hi, Try to find company ONI.de They have a one simple product FlowWatch and one fully sofisticate flowcontrol, which allowed it.
  19. Replies
    1
    Views
    618

    Re: Bad smell after production

    It is an recycled material and it can content something inside, what causes bad smell … maybe Pampers :-) Please try to go down with processing temperature as low is possible...
  20. Replies
    3
    Views
    747

    Re: more krauss issues

    You have to check and may be (probably) calibrate system pressures. Open drawings and check the pressures. I am preaty sure, that system pressure is wrong. But it is not necessary pump issue. Please...
  21. Re: Hot Plate Welding: Part Sticking & PTFE coming off

    I am talking about PTFE mirrors. The strength curve will go up with bad sutface and than it will drops down. It is a paradox. please test the parts on daily base and put results into graph. You can...
  22. Replies
    3
    Views
    1,336

    Re: Euromap telegraph questions / commands

    Variable Name = VMD-xxxxx
    {component name = EXTRF, component type = bit-string 256}
    stop of machine (0)

    yap?
  23. Re: Hot Plate Welding

    Do you have any requirements for welding quality? Also visualy OK, or are the ribs hidden after welding. PTFE is problematic. You can go down with contact speed of part and mirror. Best is move the...
  24. Replies
    5
    Views
    4,878

    Re: Nissei 20-Ton and 80-Ton Machine Specs

    try this :-)

    http://www.worthpoint.com/worthopedia/nissei-fe80s12ase-injection-molding-159119999

    be funny :-)
  25. Thread: Cross Linking

    by Pilot
    Replies
    5
    Views
    2,702

    Re: Cross Linking

    can you post a brand name and type of the material please ....
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4