Search:

Type: Posts; User: rickbatey; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    10
    Views
    1,507

    Re: Merry and Happy

    Thanks and prayers for much improved year, 2021!!
  2. Replies
    10
    Views
    1,507

    Re: Merry and Happy

    Been sick since so count your blessings of family as well. Not Covid though daughter has double pneumonia, wife bronchitis, me something in between but they have ear infections as well!! So I’m...
  3. Replies
    1
    Views
    378

    Re: Large Injection Mold Pallets

    We have two mold movers that we use to get the tools under the correct crane. One is a large heavy duty pallet Jack on steroids and the other a truck like thing you drive from on top. We store...
  4. Replies
    1
    Views
    458

    Re: Krauss Maffei

    You have to change the setting on the hold pressure stages from one mode to the other but with a KM I’m afraid you’ll be disappointed. Also, I think that’s how they tunes the electric servo pumps....
  5. Replies
    8
    Views
    786

    Re: Problem during TPE processing

    I would lower the barrel settings slightly as I believe the barrel capacity is low enough to cause cooking out of some of the additives in the resin. Also what size are the resin purchases? I ask...
  6. Replies
    7
    Views
    1,083

    Re: Unsolved ınjection problems

    I suspect your barrel settings are too high for UV package in resin. Hence to odd locations. Need to reduce the barrel sertings, screw rpm and back pressure.
    Rick
  7. Replies
    7
    Views
    1,083

    Re: Unsolved ınjection problems

    Water temperature ? Barrel temperatures ? Mold temperatures ? Screw recovery time and back pressure? Valve gate settings? Hot runner brand and style? Mold venting? Drier settings? Barrel residence...
  8. Re: New Machine Brand Decision? Help me choose!

    If you’re looking at Mucell, Engel was one of the first to assist with that technology from the start. Also, with that process you can run larger shot weights with lower clamp forces. I don’t like...
  9. Replies
    4
    Views
    890

    Re: Overmolding/Insert molding

    First off you should mold the abs and then over mold. Secondly you can purchase an add on injection unit from numerous companies now days. Most of them are available in all electric platforms for...
  10. Replies
    3
    Views
    926

    Re: Rare cosmetic defect

    To me it looks like either poor color dispersion or unmelted pellets. I would watch the screw recovery pressure at start and then check it every half hour. I think you’ll find it low at the start and...
  11. Replies
    5
    Views
    1,345

    Re: Embedded Bubbles

    In my experience with running clear resin , you never run the screw empty and you never shut the barrel heats off. You ramp them down low enough the resin won’t degrade and leave them on; say 350*F....
  12. Replies
    12
    Views
    2,277

    Re: Overmolding or insert molding?

    I ask; did you tell preheat metal inserts? Differential shrinkage can be the root cause. But I also ask did you clean/degrease inserts prior to molding? Cutting oils normally have sulphur in them...
  13. Re: Random variation on cushion and part sticking to core.

    So it appears this is a thin wall high speed press and process? I ask how long
    It takes screw to recover, do you have shut off nozzles in mold or on press, and can you monitor screw recovery...
  14. Replies
    8
    Views
    1,994

    Re: Help please, Milky Bloom/stain

    What is the width and depth of the tab gate? What is the part thickness at the gate? I think your gates should be much wider and the depth adjusted to create a better melt flow in the cavity. I also...
  15. Replies
    1
    Views
    1,001

    Re: Process Sheets (Control) Suggestions

    We use the same tolerances on all settings, like barrel or mold heats +/- 10* C, tonnage and all variables are given similar ranges. No issues for us as long as the variance sheet lists name, defect...
  16. Replies
    8
    Views
    1,994

    Re: Help please, Milky Bloom/stain

    It looks like you are shooting into sub-gated cold runner from valve gate. I think the gates are too small and shearing the melt to the point that the talc is blooming onto the surface. Sequencing...
  17. Replies
    5
    Views
    1,345

    Re: Embedded Bubbles

    I could see an additive or even the FR or UV package breaking down. One question: What do you use to purge and shut down with? Kinda looks like PE or PP contamination.
    Rick
  18. Replies
    6
    Views
    1,345

    Re: Old 250 Ton Milacron

    Sounds like the pre-fill valve doesn’t close until 2nd attempt. Be that a sticking valve or loss of clamp lock up signal I’m not sure. Could even be low pump output pressure or flow.
    I’d check and...
  19. Re: How to avoid transition marks due to change in flow rate while using Sequential gating?

    The color changes are more than likely due to the flow direction changes and enhanced by the pigment particle shape from the colorant. We’ve seen this many times and our process fill pattern could be...
  20. Replies
    4
    Views
    993

    Re: Flakes in Mold, gating?

    When I see this, I feel that the gates are dull. The dull edges of the gate create the flakes at the runner is separated from the part. Part of your issue may be that the gate edges were dulled due...
  21. Replies
    4
    Views
    1,485

    Re: Boy 50T2 no SEMI-AUTO or AUTO

    Do you have a shot size set on the machine? Is that stroke made? Injection timer set to something other than 0? Injection or hold pressures set? Pack/hold timers set ? Clamp force set? Carriage...
  22. Replies
    16
    Views
    3,021

    Re: 20% GF PP Warp

    What about melt temps? Entire mold hotter too? I only see on gate. Where are the others? I know this won’t run a decoupled process due to reminding me of plastic bowl lids; they look like potato...
  23. Replies
    9
    Views
    2,276

    Re: Krauss Maffei MC6 parameterlist

    It’s possible but I think, from the alarm , that you haven’t selected any parameters on the monitoring screen. Select them and create your list, then you should be able to print them. You can upload...
  24. Replies
    6
    Views
    1,983

    Re: Storage Box Lid Warpage

    I think you will need a short and quickly ramping downward hold pressure profile to stop this tendency. The root cause is as you said. I think a warmer mold on both halves to reduce molded in stress...
  25. Replies
    7
    Views
    1,418

    Re: Overmold Possibility

    First thing make sure you have enough part thickness to allow the inserts to become totally encapsulated within the part. You will need to support the inserts in a way that holds them in place as the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4