Page 1 of 51 12311 ... LastLast
Threads 1 to 20 of 1019

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Recovery Issues at Start-Up

    Started by PlasticNoob, 7th August 2019 06:10 PM
    • Replies: 3
    • Views: 142
    16th August 2019, 06:23 AM Go to last post
  2. Ultem and CF Peek in an aluminum mold

    Started by iamplwirtz, 13th August 2019 04:16 PM
    • Replies: 4
    • Views: 70
    16th August 2019, 06:15 AM Go to last post
  3. Soft Cap , need advice

    Started by Joel JS, 12th August 2019 10:08 PM
    • Replies: 4
    • Views: 77
    15th August 2019, 07:40 PM Go to last post
  4. Nissei Manuals Needed

    Started by Gatorpl, 12th August 2019 07:17 PM
    • Replies: 0
    • Views: 31
    12th August 2019, 07:17 PM Go to last post
  5. Van Dorn 300HT excessive noise

    Started by MNDesign81, 22nd June 2019 04:04 PM
    • Replies: 7
    • Views: 357
    4th August 2019, 12:19 PM Go to last post
  6. Cool DC53 & XW41 recommended hardness HRC

    Started by Puravintha, 2nd August 2019 04:32 AM
    • Replies: 0
    • Views: 67
    2nd August 2019, 04:32 AM Go to last post
  7. Proper Short Shot - What do you think

    Started by The Rookie, 29th July 2019 05:25 PM
    • Replies: 3
    • Views: 172
    31st July 2019, 02:10 PM Go to last post
  8. Flow Lines?

    Started by The Rookie, 18th July 2019 08:14 PM
    • Replies: 5
    • Views: 292
    29th July 2019, 06:22 PM Go to last post
  9. Kawaguchi K 480 B settings

    Started by Shaft, 23rd July 2019 11:39 AM
    • Replies: 2
    • Views: 149
    25th July 2019, 11:42 AM Go to last post
  10. Cincinnati/Milacron: Opinions on presses & service

    Started by joeprocess, 3rd May 2017 08:55 PM
    • Replies: 2
    • Views: 913
    18th July 2019, 07:47 PM Go to last post
  11. Delta E Color Tolerance

    Started by bpolymn, 3rd July 2019 08:34 PM
    color, delta e, lab
    • Replies: 9
    • Views: 429
    15th July 2019, 09:06 PM Go to last post
  12. Small plastic injection molding: Boy vs Arburg

    Started by Reckless, 4th December 2017 02:56 AM
    arburg, boy
    • Replies: 7
    • Views: 2,126
    13th July 2019, 04:49 PM Go to last post
  13. Switching on machine pressure versus Stroke

    Started by iautry1973, 15th November 2018 04:55 PM
    • Replies: 6
    • Views: 787
    2nd July 2019, 05:42 PM Go to last post
  14. Best way to find an industrial mechanic?

    Started by bparker25, 2nd July 2019 02:29 AM
    • Replies: 0
    • Views: 139
    2nd July 2019, 02:29 AM Go to last post
  15. Question Babyplast Alternatives for micro molding?

    Started by Reckless, 9th December 2017 04:53 PM
    • Replies: 4
    • Views: 2,140
    1st July 2019, 06:39 PM Go to last post
  16. Defects

    Started by Ulynovsk, 23rd December 2018 06:23 PM
    • Replies: 6
    • Views: 1,003
    28th June 2019, 02:01 PM Go to last post
  17. Cavities blockage

    Started by holar09, 11th February 2019 07:33 PM
    • Replies: 9
    • Views: 736
    28th June 2019, 01:55 PM Go to last post
  18. Exclamation milacron maxima 580wp issue

    Started by maintTechBrian, 21st June 2019 06:35 AM
    • Replies: 2
    • Views: 213
    25th June 2019, 06:25 PM Go to last post
  19. Injection Molding Mexico

    Started by vermaad, 17th June 2019 07:29 PM
    • Replies: 2
    • Views: 281
    17th June 2019, 10:52 PM Go to last post
  20. Cincinnatti Milacron: Looking for motherboard

    Started by Flash, 9th March 2017 12:49 PM
    • Replies: 1
    • Views: 954
    12th June 2019, 05:44 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •