Page 1 of 64 1231151 ... LastLast
Threads 1 to 20 of 1269

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Back Pressure

    Started by yangozugur, 11th March 2021 12:09 PM
    • Replies: 8
    • Views: 3,306
    5th December 2021, 07:44 PM Go to last post
  2. Shop recommendations

    Started by Robert24, 10th November 2021 02:41 AM
    • Replies: 3
    • Views: 385
    5th December 2021, 07:32 PM Go to last post
  3. Molding nylon with photoluminescent pigment and UV stabilizer

    Started by Vince, 1st December 2021 08:21 AM
    • Replies: 1
    • Views: 99
    4th December 2021, 01:36 AM Go to last post
  4. Melt Flow İndex

    Started by yangozugur, 30th September 2021 04:43 PM
    • Replies: 3
    • Views: 1,695
    3rd December 2021, 06:58 PM Go to last post
  5. BMC Polyester Composites

    Started by yangozugur, 4th November 2021 11:04 AM
    • Replies: 1
    • Views: 401
    15th November 2021, 07:56 PM Go to last post
  6. Hot Runner/Tolerance Issues

    Started by moldingppm, 11th November 2021 07:07 AM
    • Replies: 2
    • Views: 392
    14th November 2021, 01:34 PM Go to last post
  7. Krauss Maffei 160-750 CX Data collection.

    Started by usercvk, 2nd November 2021 05:47 PM
    • Replies: 1
    • Views: 437
    12th November 2021, 02:50 PM Go to last post
  8. Undercuts Design Guideline

    Started by yangozugur, 11th November 2021 01:08 PM
    • Replies: 1
    • Views: 337
    11th November 2021, 01:09 PM Go to last post
  9. Masterbatch material dispersion

    Started by GloriousLighting, 29th October 2021 01:51 PM
    • Replies: 3
    • Views: 477
    8th November 2021, 11:50 AM Go to last post
  10. Netstal synergy 1200-460

    Started by peloflex, 25th October 2021 06:49 AM
    • Replies: 2
    • Views: 638
    26th October 2021, 07:22 AM Go to last post
  11. Oroglas SG-7

    Started by DanBarrass, 19th October 2021 05:25 PM
    • Replies: 0
    • Views: 1,010
    19th October 2021, 05:25 PM Go to last post
  12. Material type

    Started by Robert24, 13th October 2021 06:46 PM
    • Replies: 0
    • Views: 1,492
    13th October 2021, 06:46 PM Go to last post
  13. Dosing Problem

    Started by Viju vj, 6th October 2021 08:34 AM
    • Replies: 1
    • Views: 1,621
    8th October 2021, 05:05 AM Go to last post
  14. Clamp Force

    Started by yangozugur, 7th October 2021 09:50 AM
    • Replies: 1
    • Views: 1,645
    8th October 2021, 02:03 AM Go to last post
  15. Question about pixels vs actual EVA molds

    Started by APBsayin, 5th October 2021 11:08 PM
    • Replies: 0
    • Views: 1,484
    5th October 2021, 11:08 PM Go to last post
  16. How was this molded?

    Started by Swisscheese, 28th September 2021 01:19 PM
    • Replies: 2
    • Views: 1,645
    5th October 2021, 02:17 PM Go to last post
  17. Getting ready to test

    Started by Chuck H, 4th October 2021 09:46 PM
    • Replies: 2
    • Views: 1,528
    4th October 2021, 10:23 PM Go to last post
  18. Material Drooling

    Started by Viju vj, 19th September 2021 06:18 AM
    • Replies: 5
    • Views: 1,754
    29th September 2021, 11:26 PM Go to last post
  19. Ultra-sonic cleaning of mold components

    Started by joeprocess, 9th September 2021 04:10 PM
    • Replies: 2
    • Views: 1,720
    28th September 2021, 11:45 PM Go to last post
  20. Trueblood 30-ton help needed

    Started by Chuck H, 21st September 2021 12:21 AM
    • Replies: 6
    • Views: 1,714
    26th September 2021, 11:29 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •