Page 1 of 44 12311 ... LastLast
Threads 1 to 20 of 875

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Vinyl Record Duplication - best materials to use?

    Started by Connor2303, 21st July 2018 02:58 PM
    2 part mould, injection moulding, resin, silicone, vinyl record
    • Replies: 0
    • Views: 21
    21st July 2018, 02:58 PM Go to last post
  2. Living hinge advice

    Started by mikesydwest, 14th July 2018 03:31 PM
    • Replies: 11
    • Views: 160
    21st July 2018, 07:52 AM Go to last post
  3. Van Dorn 120 ton Hydraulic Chatter

    Started by SRPlasPros, 29th June 2018 07:26 PM
    hydraulic, van dorn
    • Replies: 2
    • Views: 108
    20th July 2018, 10:01 PM Go to last post
    • Replies: 2
    • Views: 44
    20th July 2018, 01:56 PM Go to last post
    • Replies: 1
    • Views: 33
    19th July 2018, 12:19 AM Go to last post
  4. FLIR or other infrared camera as a processing aide

    Started by Joel JS, 16th July 2018 10:03 PM
    • Replies: 2
    • Views: 56
    17th July 2018, 03:27 PM Go to last post
  5. TOYO Si-300 book!

    Started by SRPlasPros, 16th July 2018 08:18 PM
    • Replies: 0
    • Views: 36
    16th July 2018, 08:18 PM Go to last post
  6. Part Design Feasibility Question

    Started by stephenof, 10th July 2018 08:51 PM
    • Replies: 5
    • Views: 111
    13th July 2018, 08:12 PM Go to last post
  7. A simple mold to help determine material shrinkage

    Started by Puravintha, 5th July 2018 01:25 AM
    • Replies: 2
    • Views: 145
    11th July 2018, 05:56 AM Go to last post
  8. Galvanized Pipe or Plastic Pipe for Plant water supply?

    Started by tbramel, 29th June 2018 07:52 AM
    • Replies: 8
    • Views: 203
    10th July 2018, 08:00 PM Go to last post
  9. Question Using a Hardened Cavity and a Pre-Hardened Core

    Started by raytk91, 28th June 2018 08:27 AM
    steels and inserts
    • Replies: 1
    • Views: 102
    2nd July 2018, 04:53 PM Go to last post
  10. Post Fiber orientation.

    Started by Mandar, 29th June 2018 11:21 AM
    fiber orientation, materials, plastics processing
    • Replies: 3
    • Views: 137
    2nd July 2018, 04:47 PM Go to last post
  11. Insert mold stainless steel rod using acetal

    Started by sjoseph, 27th June 2018 03:51 AM
    acetal, insert molding, rod, stainless steel
    • Replies: 3
    • Views: 126
    28th June 2018, 08:51 PM Go to last post
  12. noise at start of opening phase

    Started by mohamed, 26th June 2018 01:57 PM
    • Replies: 6
    • Views: 150
    27th June 2018, 04:56 PM Go to last post
  13. Heater Band Overheating HELP!

    Started by Bsim1776, 25th June 2018 07:05 PM
    band, heater, overheating
    • Replies: 5
    • Views: 156
    27th June 2018, 04:55 PM Go to last post
  14. Thermolator Help!!

    Started by SRPlasPros, 21st June 2018 06:28 PM
    thermolators
    • Replies: 6
    • Views: 180
    25th June 2018, 06:06 PM Go to last post
  15. Material cushion variation

    Started by nemanja, 26th April 2018 06:09 PM
    2 Pages
    1 2
    • Replies: 22
    • Views: 1,065
    22nd June 2018, 01:37 PM Go to last post
  16. Toyo 200 Ton SI-200 III PLCS-11 Error 495

    Started by SRPlasPros, 21st June 2018 06:34 PM
    error code 495, plcs-11, toyo
    • Replies: 0
    • Views: 74
    21st June 2018, 06:34 PM Go to last post
  17. Cheap/DIY Thermolator?

    Started by moldingppm, 2nd June 2018 05:47 AM
    • Replies: 3
    • Views: 216
    21st June 2018, 01:35 AM Go to last post
    • Replies: 4
    • Views: 642
    20th June 2018, 10:38 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •