Page 8 of 67 FirstFirst ... 6789101858 ... LastLast
Threads 141 to 160 of 1328

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Question Advice for scientific molding on a Chinese injection machine - newbie

    Started by trynix, 12th February 2021 08:30 PM
    5 Attachment(s)
    • Replies: 3
    • Views: 534
    Crabstix
    17th February 2021, 10:00 AM Go to last post

  2. Too much shrinkage

    Started by moldingppm, 9th February 2021 10:10 PM
    1 Attachment(s)
    • Replies: 4
    • Views: 20,979
    moldingppm
    16th February 2021, 06:43 AM Go to last post

  3. burn marks?

    Started by yangozugur, 10th February 2021 03:20 PM
    1 Attachment(s)
    • Replies: 4
    • Views: 504
    yangozugur
    15th February 2021, 06:57 AM Go to last post

  4. Smile How accurate are Mold Flows?

    Started by Joel JS, 8th February 2021 03:29 PM
    • Replies: 3
    • Views: 39,688
    Suhas
    12th February 2021, 04:11 PM Go to last post

  5. Best Auxillaries Setup for 270TIM machine for preforms

    Started by pakpolymers, 8th February 2021 11:12 AM
    • Replies: 1
    • Views: 2,188
    Bryan E
    10th February 2021, 10:13 AM Go to last post

  6. Conformal Cooling equipment

    Started by nimrodk93, 9th February 2021 06:56 PM
    • Replies: 1
    • Views: 386
    Bryan E
    10th February 2021, 09:25 AM Go to last post

  7. Inconsistent Shrinkage Rates

    Started by DylanJackson, 26th January 2021 09:04 PM
    • Replies: 6
    • Views: 3,847
    Josue
    9th February 2021, 10:41 PM Go to last post

  8. Problem during TPE processing

    Started by greg8811, 20th November 2020 08:34 AM
    tpe
    • Replies: 9
    • Views: 6,128
    Nick Liao
    2nd February 2021, 07:31 AM Go to last post

  9. mold flow review checklist

    Started by Nick Liao, 2nd February 2021 06:57 AM
    • Replies: 0
    • Views: 2,191
    Nick Liao
    2nd February 2021, 06:57 AM Go to last post

  10. Question mold change check list

    Started by carnold, 23rd January 2021 04:37 AM
    2 Attachment(s)
    • Replies: 4
    • Views: 741
    carnold
    27th January 2021, 04:41 AM Go to last post

  11. Engel Machine keeps stopping

    Started by Xpump, 28th October 2020 07:15 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 3,433
    Xpump
    27th January 2021, 04:22 AM Go to last post

  12. Angry Vista VT300-34 No High pressure

    Started by MaddDoctor39, 6th January 2021 07:57 PM
    1 Attachment(s)
    • Replies: 7
    • Views: 50,846
    ijchan223
    23rd January 2021, 02:49 AM Go to last post

  13. Ram speed

    Started by yangozugur, 15th January 2021 07:50 AM
    • Replies: 4
    • Views: 570
    yangozugur
    22nd January 2021, 08:09 AM Go to last post

  14. KM 175/700/C2 35 mm Screw Tip Issue

    Started by Jakegaspari, 20th January 2021 04:14 PM
    • Replies: 3
    • Views: 357
    Pilot
    21st January 2021, 11:14 AM Go to last post

  15. Unhappy KM 175/700/C2 35 mm Screw is stuck

    Started by Jakegaspari, 16th January 2021 11:33 PM
    • Replies: 3
    • Views: 36,571
    Pilot
    19th January 2021, 05:02 PM Go to last post

  16. Arburg problem

    Started by Matt Gow, 23rd September 2016 10:43 AM
    arburg, injection, problem
    • Replies: 9
    • Views: 15,900
    ijchan223
    19th January 2021, 04:45 AM Go to last post

  17. What is this defect?

    Started by moldingppm, 2nd December 2020 04:07 PM
    1 Attachment(s)
    • Replies: 12
    • Views: 1,751
    Jendalf
    18th January 2021, 09:52 AM Go to last post

  18. Thank You All

    Started by Suhas, 17th January 2021 03:25 AM
    • Replies: 0
    • Views: 33,977
    Suhas
    17th January 2021, 03:25 AM Go to last post

  19. Wintec machines

    Started by Aquaphor_Co., 15th January 2021 01:33 PM
    wintec
    • Replies: 0
    • Views: 36,639
    Aquaphor_Co.
    15th January 2021, 01:33 PM Go to last post

  20. Chiller water is getting dirty and brownish color

    Started by RAMESHBABU, 25th April 2020 02:18 PM
    chiller, cooling tower, injection molding machine
    • Replies: 9
    • Views: 110,974
    smartvn2020
    11th January 2021, 08:01 AM Go to last post
Page 8 of 67 FirstFirst ... 6789101858 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules