Page 40 of 46 FirstFirst ... 303839404142 ... LastLast
Threads 781 to 800 of 913

Forum: General Injection Molding

Post all Injection Molding Related questions here.
Please Note:
1. This is not an advertising forum - please do not register to advertise your services here.
2. Please report if you receive any spam through private messaging.

  1. Water temperatures

    Started by stennerpumpsmolding, 20th February 2013 11:46 PM
    molding temperatures, water temperatures
    • Replies: 6
    • Views: 8,149
    26th February 2013, 05:13 AM Go to last post
  2. gate seal study.

    Started by sublime1, 27th August 2012 03:38 PM
    • Replies: 10
    • Views: 5,706
    19th February 2013, 04:29 AM Go to last post
  3. encapsulating diodes

    Started by kelley, 20th July 2012 02:13 AM
    • Replies: 12
    • Views: 6,418
    7th February 2013, 02:22 PM Go to last post
  4. Adhesion issue with double Overmold (Pebax)

    Started by Jackson, 6th February 2013 05:18 AM
    • Replies: 3
    • Views: 2,988
    6th February 2013, 09:04 PM Go to last post
  5. Adequate water cooling

    Started by Farkas, 6th February 2013 02:44 PM
    • Replies: 3
    • Views: 2,367
    6th February 2013, 07:37 PM Go to last post
  6. Few questions

    Started by moldingppm, 5th February 2013 09:01 AM
    • Replies: 3
    • Views: 2,132
    6th February 2013, 01:09 AM Go to last post
  7. Micro Parts

    Started by brentb, 1st December 2011 05:32 AM
    • Replies: 4
    • Views: 2,808
    30th January 2013, 07:24 AM Go to last post
  8. Air Blow question

    Started by moldingppm, 19th November 2012 04:27 PM
    • Replies: 10
    • Views: 6,733
    29th January 2013, 05:29 PM Go to last post
  9. gas assist question

    Started by jbaredesign, 12th December 2012 03:43 AM
    • Replies: 6
    • Views: 3,186
    28th January 2013, 07:50 PM Go to last post
  10. Small Injection Machine Recommendations

    Started by macdonmr, 2nd October 2012 01:40 PM
    equipment, low tonage, small machine, small shot
    • Replies: 7
    • Views: 6,316
    28th January 2013, 01:41 AM Go to last post
  11. ways to improve

    Started by sublime1, 9th January 2013 03:24 AM
    • Replies: 13
    • Views: 6,884
    21st January 2013, 11:44 PM Go to last post
  12. Wink Worst part molded

    Started by ATI K ID, 22nd August 2012 05:24 AM
    • Replies: 7
    • Views: 4,401
    17th January 2013, 06:32 PM Go to last post
  13. Flash at the nozzle

    Started by finerdetail, 3rd December 2012 04:40 PM
    • Replies: 19
    • Views: 9,811
    5th January 2013, 11:37 PM Go to last post
    • Replies: 4
    • Views: 2,737
    2nd January 2013, 07:20 PM Go to last post
  14. Thank you & happy new year !

    Started by Suhas, 2nd January 2013 05:33 AM
    • Replies: 0
    • Views: 1,507
    2nd January 2013, 05:33 AM Go to last post
  15. Plastisizer Trap

    Started by joeprocess, 7th December 2012 01:59 PM
    • Replies: 3
    • Views: 2,359
    18th December 2012, 10:06 PM Go to last post
  16. Suggestions for a 48 or 72 zone hot runner controller

    Started by tfrounfe, 12th December 2012 09:49 PM
    • Replies: 8
    • Views: 3,981
    17th December 2012, 08:53 PM Go to last post
  17. Technical support about a Toshiba 390iSG

    Started by arturo aguirre, 10th December 2012 11:58 PM
    • Replies: 2
    • Views: 2,183
    11th December 2012, 05:54 PM Go to last post
  18. Help with Boy 22S

    Started by tphall, 19th November 2012 08:25 PM
    • Replies: 3
    • Views: 2,215
    6th December 2012, 12:33 AM Go to last post
  19. Tolerances On Mouldings

    Started by processtech, 28th November 2012 08:17 AM
    • Replies: 4
    • Views: 3,092
    29th November 2012, 10:18 PM Go to last post

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •